Oil Purification products
Air Compressor Filter
Air Compressor Inline Filter
Water purification equipment
Air Purification Products
Brand Name: PALL
Model Number: LCS2B1AH
Nominal filtration rating:分离级(PTFE 涂层网,液相)
Application:炼厂成品油装车台、油库、燃料库过滤分离器
Operating pressure:
Working temperature: 按工况介质
Replacement or not:Replacement
The second stage of a liquid fuel filter separator is the separator cartridge, listed with the Gas Filter Element family. It is made of a special hydrophobic material, a Teflon coated screen mesh. When fuel passes through, water droplets are held outside the element while the fuel enters and exits through the outlet; blocked droplets gather, grow and settle into the water storage section below. The separator filter element LCS2B1AH replacement is supplied in the 40 inch format used in refinery and terminal filter separator vessels.
| Cross-reference | PALL LCS2B1AH |
| Length | 40 inch |
| Working phase | Liquid fuel service |
| Media | Hydrophobic Teflon coated screen mesh |
| Surface property | Hydrophobic and lipophilic |
| Function | Blocking and drainage of coalesced water droplets |
| Working position | Second stage, after the coalescing cartridge in the same vessel |
| Typical service | Refinery product loading terminal, tank farm and fuel depot |
At a refinery product loading terminal, gasoline and diesel pass the coalescing stage and then this separator before the loading arm. Water held on the outside of the screen drains to the sump, and dry product goes to the truck or the pipeline. A damaged separator carries water into the compartment, which shows up later as filter blocking at the customer's dispenser or as corrosion in storage. Terminals therefore trend outlet water content rather than rely on a fixed calendar, and keep one spare set per bay. Upstream coalescing selection is covered in the replacement filter element catalogue.
Teflon coating gives strong hydrophobicity with lipophilicity, so water is repelled while fuel passes at low pressure loss. The coating resists sticking of gums and heavy deposits, keeping the drainage path open between cleaning cycles. The 40 inch format is a direct dimensional replacement, so change-out procedure and element count stay as the OEM arrangement. A 512 piece shipment for a petrochemical project confirms dimensional repeatability in terminal service. Vessel-side hardware is indexed on hydraulic equipment.
The plant has supplied 512 pieces of LCS2B1AH equivalent cartridges for a petrochemical project, and holds further references for PALL CS604LGH13 and CC3LG02H13, PECO PCHG-336 and FG-536. Separator and coalescer cartridges come off the same line so a terminal can order a matched pair with one delivery. For cross-reference and outlet water target review, contact our engineering team, and see complete skids under Industrial Oil Purification Equipment.
Q1: How does the separator differ from the coalescer?
A1: The coalescer is hydrophilic and merges small droplets; the separator is hydrophobic and blocks the enlarged droplets so they drain instead of leaving with the fuel.
Q2: What material provides the separation effect?
A2: A Teflon coated screen mesh with hydrophobic and lipophilic surface properties, so water stays outside while fuel passes through.
Q3: When should the 40 inch cartridge be changed?
A3: On rising differential pressure, on an upward trend in outlet water content, or at the vessel inspection interval set by the terminal.
Q4: Can it be installed without a coalescing stage?
A4: Not properly; without coalescence the droplets remain too small for the screen to block and drain, so separation efficiency collapses.
Q5: Does it suit both horizontal and vertical vessels?
A5: The cartridge principle suits both orientations; confirm element length, end cap and seal against the vessel drawing before ordering.
Reference: API 1581 fuel filter separator specification | Gas Filter Element catalogue reference
![]()
![]()
![]()
![]()
![]()
![]()
![]()
![]()