Position: HOME > Product > Air Purification Products > Air Filter >
LF 05a Gas Turbine Air Intake Filter Cartridge 408 mm OD 875 mm Length 33.2 Square Meter Replacement For Donaldson Air Filter
  • LF 05a Gas Turbine Air Intake Filter Cartridge 408 mm OD 875 mm Length 33.2 Square Meter Replacement For Donaldson Air Filter

LF 05a Gas Turbine Air Intake Filter Cartridge 408 mm OD 875 mm Length 33.2 Square Meter Replacement For Donaldson Air Filter

Read 1 Reviews23 Q&As Write a Review
LF 05a gas turbine air intake filter cartridge is 408 mm OD, 293 mm ID and 875 mm long with 33.2 m² filter area, supplied as a replacement for Donaldson air filters in power plant and compressor intake service.

PARAMETER

Brand Name: Donaldson
Model Number: LF-05a
Nominal filtration rating:按介质等级(进气过滤)
Application:燃气轮机进气、空压机进气
Operating pressure:
Working temperature: 按介质(常规进气工况)
Replacement or not:Replacement

Product Overview

Gas turbine intake cartridges are part of the air purification equipment range and are built for gas turbines and air compressors operating in dusty, coastal or polluted sites. Media is normally a mix of polyester, cellulose and nanofiber, giving better pleat ability and dimensional stability than single-layer paper. LF-05a: cylinder shape, OD 408 mm, ID 293 mm, length 875 mm (34.5 in), filter area 33.2 m². The catalogue notes acceptance of Donaldson air filter replacement.

Basic Technical Parameters

ModelLF-05a
ShapeCylinder
Outer diameter408 mm
Inner diameter293 mm
Length875 mm (34.5 in)
Filter area33.2 m²
MediaPolyester / cellulose / nanofiber blend
Cross-referenceDonaldson air filter replacement accepted

Power Plant And Compressor Scenario

An inland gas turbine station pulls intake air across a field of cartridges; fine dust and pollen load the outer surface while the turbine keeps its output. The 33.2 m² area per cartridge holds a long service interval and keeps inlet differential pressure within the compressor's allowance. On coastal sites the same element handles salt aerosol, where dimensional stability of the blended media prevents pleat sag under humidity cycling. A pre-filter stage of pocket bag filter media ahead of the cartridges further reduces the load, and change-out is scheduled on measured pressure drop.

Product Advantages

Blended polyester, cellulose and nanofiber media deliver high filtration efficiency for dust and contaminants in polluted environments while retaining pleat strength. The cylindrical format fits existing intake plates without modification, and the large area per element keeps element count and change labor low. Dimensional stability under moisture and pulse cleaning avoids bypass gaps at the end seals, which protects compressor blades from erosion.

Manufacturer And Factory Strength

Intake cartridges are pleated on automated lines with end-cap bonding and gasket inspection per batch, and Donaldson cross-references are documented against the catalogue list (LF-01 to LF-06, including cone and twist-lock versions). Plants also sourcing lubricant-side consumables can use the hydraulic equipment range from the same factory, including the hydraulic oil filter machine series. For intake house layout and element count, contact our engineering team.

FAQ

Q1: Is LF-05a a direct replacement for Donaldson cartridges?
A1: The catalogue states acceptance of Donaldson air filter replacement; confirm the exact OEM part number and end-cap style before ordering.

Q2: What is the difference between LF-05a and LF-05b?
A2: Both are 408 mm OD and 293 mm ID; LF-05a is 875 mm long with 33.2 m², LF-05b is 559 mm long with 21.6 m².

Q3: Why use nanofiber in intake media?
A3: Nanofiber raises fine-particle efficiency without high pressure drop, protecting compressor blades from submicron dust.

Q4: How often should intake cartridges be replaced?
A4: On differential pressure trend and site dust load; do not wait for alarm-level restriction, since compressor efficiency drops earlier.

Q5: Are conical versions available for the same house?
A5: Yes, LF-01 to LF-04 cone versions cover 445-324 mm and 408-324 mm top diameters for conical plate designs.

Reference: ISO 29461 air intake filter systems for rotary machinery | air cleaning


{sval:sql sql='SELECT n_parameter FROM dede_addonarticle WHERE aid = ~aid~ ' } {/sval:sql}
{sval:sql sql='SELECT n_parameter FROM dede_addonarticle WHERE aid = ~aid~ ' } {/sval:sql}