Position: HOME > Product > Air Purification Products > Air Dust Collector >
MC30 Pulse Jet Baghouse Dust Collector 100 Filter Bags 122 Square Meter For Cement Mill And Crusher Dust Control
  • MC30 Pulse Jet Baghouse Dust Collector 100 Filter Bags 122 Square Meter For Cement Mill And Crusher Dust Control

MC30 Pulse Jet Baghouse Dust Collector 100 Filter Bags 122 Square Meter For Cement Mill And Crusher Dust Control

Read 2 Reviews23 Q&As Write a Review
MC30 pulse jet baghouse dust collector uses 100 needle felt bags of 130 mm diameter and 3000 mm length, giving 122 m² filter area at 14400 CMH airflow for cement mill and crusher dedusting.

PARAMETER

Brand Name:
Model Number:
Nominal filtration rating:
Application:
Operating pressure:
Working temperature:
Replacement or not:Replacement

Product Overview

The MC series is the baghouse dust collector platform in our air line, built on needle felt bags and reverse pulse compressed air cleaning. Dust-laden gas enters the filter chamber and is retained on the bag surface; clean air exits from the top. When differential pressure reaches the set value, compressed air is blown into the bag centers through nozzles, the bag expands and the dust cake falls into the hopper. MC30 carries 100 bags of φ130 × 3000 mm, 122 m² area, and 14400 CMH airflow.

Basic Technical Parameters

ModelMC30
Bag sizeφ130 mm × L3000 mm
Bag quantity100 pieces
Filter area122 m²
Airflow14400 CMH
Cleaning methodReverse pulse compressed air
StructureSingle module / multi module

Cement Mill And Crusher Scenario

A cement grinding station discharges dust from the mill outlet, bucket elevator and clinker crusher. MC30 at 14400 CMH covers the mill vent and transfer points, with bags long enough to keep air-to-cloth ratio low in a dusty stream. The inlet deflector knocks down coarse particles before they reach the bags, protecting the needle felt and extending service life. Collected cement dust returns to the process through the screw conveyor and rotary valve rather than going to waste, and the whole air cleaning equipment train runs under PLC control with a differential pressure gauge on the clean side.

Product Advantages

Needle felt media delivers high efficiency at low pressure drop, so the system works at the lowest energy consumption for the required airflow. The pulse valve chamber is separated from the dirty side to protect valves and reduce cleaning noise. Each module ships pre-assembled in a standard container, cutting site welding, and modular heights adapt to the available airflow. Access doors on top allow bag and cage replacement without entering the  dirty chamber. Where the building requires a final supply stage, a pocket bag filter bank follows the collector.

Manufacturer And Factory Strength

Baghouse modules, filter bags, cages and accessories are produced in one plant, so media, cage and pulse parts match dimensionally. Our installations cover cement, steel, foundry, asphalt, rubber and mineral processing sites in more than 20 countries. Systems can be combined with the hydraulic filter cartridge programme for plants that also maintain hydraulic equipment on site. For air-to-cloth ratio and bag count verification, contact our engineering team.

FAQ

Q1: What airflow does MC30 handle?
A1: 14400 CMH with 100 bags of φ130 × 3000 mm, giving 122 m² of filter area.

Q2: Which bag media suits cement dust?
A2: Polyester needle felt with water and oil repellent finish is usual; for higher temperature points choose glass fiber or PPS needled felt.

Q3: Can two units run in parallel?
A3: Yes, modules can be paralleled for continuous production, with one unit on cleaning while the other filters.

Q4: How is cleaning triggered?
A4: By differential pressure across the bags or by a fixed timer in the pulse controller, with pulse width and interval adjustable.

Q5: Is site welding required for installation?
A5: No, each module is pre-installed at the factory and shipped in a standard container for bolted assembly on site.

Reference: GB/T 6719 baghouse dust collector specification | baghouse dust collector


{sval:sql sql='SELECT n_parameter FROM dede_addonarticle WHERE aid = ~aid~ ' } {/sval:sql}
{sval:sql sql='SELECT n_parameter FROM dede_addonarticle WHERE aid = ~aid~ ' } {/sval:sql}